Extreme Networks e" series Przewodnik Instalacji Pobierz pdf (Strona 95)

Installing Optional Features

Consolidated "e" Series Hardware Installation Guide 95

1 Remove the EPS-160 from the packing material.

2 Insert the EPS-160 into the front of the EPS-T.

3 Tighten the provided thumbscrews to secure the power supply to the tray.

4 Follows steps 7 through 9 on page 93.

Removing an EPS-160 from the EPS-T

To remove an EPS-160 from an EPS-T:

1 Disconnect the AC by removing the plug from the wall

2 Disconnect the AC power cord from the EPS-160.

3 Remove the redundant power cable from the EPS-160.

4 Loosen the thumbscrews on the front of the tray and slide the EPS out of the EPS-T.

1 2 ... 90 91 92 93 94 95 96 97 98 99 100 ... 111 112

Consolidated “e” Series 1
Hardware Installation Guide 1
Contents 3
Part 2 Switch Overview 4
Part 3 Switch Installation 5
Part 4 Accessory Installation 5
Part 5 Appendixes 6
Introduction 7
Conventions 8
Related Publications 8
About This Guide 9
Switch-Specific Information 10
Common Information 10
Preparing for Installation 11
Summit “e” Series and Models 13
Software Features 14
Summit 300 Features 15
Summit 400 Features 16
Port Connections 18
Following Safety Information 18
Software Images 19
Full-Duplex Support 19
2 Site Preparation 21
Planning Your Site 22
Meeting Site Requirements 22
Building and Electrical Codes 23
Wiring Closet Considerations 23
Country Requirements 24
Securing the Rack 26
Cabling Standards 27
Installing Cable 28
Fiber Optic Cable 29
Cable Distances 30
Site Preparation 32
RJ-45 Connector Jackets 33
Meeting Power Requirements 34
Power Supply Requirements 35
AC Power Cable Requirements 35
Replacing the Power Cable 36
UPS Features 36
Selecting a UPS 36
Applicable Industry Standards 37
Switch Overview 39
Summit 200 Series Switches 41
Summit 200 Switch Rear View 42
Summit 200 Switch LEDs 43
Console Port 44
Full-Duplex 46
4 Summit 300 Switch Overview 47
Summit 300-24 Switch LEDs 48
Summit 300-48 switch View 50
Summit 300-48 Switch 51
LED Behavior 52
Summit 300 Automatic Failover 53
Summit 300-48 53
Summit 300-48 Rear View 54
Load Sharing Power Supplies 55
Summit 300 Switch Overview 56
Summit 400-48t Switch 57
Summit 400 Rear View 58
Summit 400 Switch LEDs 59
Switch Installation 63
6 “e” Switch Installation 65
Rack Mounting 66
(Mini-GBIC) 67
Removing a Mini-GBIC 68
Inserting a Mini-GBIC 69
Logging In for the First Time 71
“e” Switch Installation 72
Accessory Installation 73
Summit 300 Optional Features 75
Rack-mounting the EPS-LD unit 76
Connecting the EPS-LD unit 77
Power LED Indicates 78
Green, solid 78
Removing an EPS-LD unit 79
LB48019A 80
LB48020A 81
Retaining bracket screw 82
Bracket screws 83
LED Visual Indicators 84
Figure 29: Power supply LEDs 85
Installing Optional Features 89
Card edge 90
Rack Mounting the EPS-T 92
ES4K021A 94
Appendixes 97
A Safety Information 99
Power Cable 100
Optical Safety 100
Lithium Battery 101
Safety Information 102
Common Switch Specifications 103

Komentarze do niniejszej Instrukcji

Brak uwag

Extreme Networks e" series Przewodnik Instalacji Strona 95

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Switche sieciowe Extreme Networks e" series