Extreme Networks Summit WM Series Podręcznik Użytkownika Strona 167
- Strona / 228
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Summit WM-Series WLAN Switch and Altitude Access Point Software Version 1.0 User Guide
167
A Summit WM-Series Switch Software system
states and LEDs
Summit WM-Series Switch system states and LEDs
The Summit WM-Series Switch has the two system states: Standby and Active.
It enters “Standby” when shut down in the Summit WM-Series Switch Configuration – System Maintenance
screen. The Summit WM-Series Switch:
● sends control message to Altitude AP to enter “Standby” state
● will not handle any wireless traffic or sessions
● disables DHCP, Policy Manager, Security Manager, Altitude AP Manager, Redirector
● remains on the wired network
It enters “Active” state on startup in the user interface. The Summit WM-Series Switch can now respond
to the Altitude AP's “discover” message by returning a message that the Altitude AP can enter the
“active” state.
The activity and traffic on the Summit WM-Series Switch can be monitored via three LEDs on the back
of the Summit WM-Series Switch: Link, Status, Activity.
The three LEDs perform the following functions:
● Link LED: Displays the link status of management port Ethernet link as seen by the system software.
● Status LED: Indicates the state of the CM from software point of view, normal operation, whether
processes have gone down and are restarting, etc.
● Activity LED: Indicates the amount of traffic carried to and from Altitude APs.
The Link LED is only seen at the back of the Summit WM-Series Switch. The Status and Activity LEDs
can be seen from both the front and the back of the Summit WM-Series Switch.
The sequence of the Status and Activity LEDs is as follows:
System State Status LED Activity LED
Power up Off Off
Services started: WDTSTAT installed (init.d starts services) Blinking Amber Off
Startup Manager Task started Solid Amber Blinking Amber
Startup Manager Task completes startup – all components started Solid Green Blinking green, if traffic
Blank, if no traffic
- Table of Contents 3
- Formatting conventions 10
- Documentation feedback 10
- Protocols and standards 11
- Regulatory information 11
- About this Guide 12
- Conventional wireless LANS 13
- Wireless AP 15
- Summit WM 15
- Wireless Controller 15
- Network traffic flow 18
- Network security 19
- Policy: packet filtering 21
- Mobility and roaming 21
- Availability 22
- Quality of Service (QoS) 22
- Data ports (4 or 2) 24
- Management ports 24
- Configuration steps: overview 31
- Enabling the product key 31
- Setting up the data ports 32
- Port Type or Function 34
- Setting up static routes 35
- Setting up OSPF Routing 36
- Define port exception filters 40
- 4 Altitude AP: startup 41
- Installing the Altitude APs 43
- Set the discovery timers 45
- Discovery and registration 46
- Registration after discovery 48
- Altitude AP access approval 49
- ● 802.11 b/g (2.4 GHz radio) 53
- ● 802.11a (5 GHz radio) 53
- Adding a Altitude AP manually 56
- Auto Cell software 58
- Configure Auto Cell software 59
- Altitude AP: startup 60
- Introduction 61
- What is a WM-AD? 62
- Topology of a WM-AD 62
- Filtering for a WM-AD 64
- Setting up a new WM-AD 66
- Global Settings for a WM-AD 68
- Topology for a WM-AD 71
- Use DHCP Relay for the WM-AD 74
- Topology for a WM-AD for AAA 75
- Authentication for a WM-AD 76
- ● No Captive Portal Support 80
- Captive Portal” on page 87) 81
- Accounting for a WM-AD 84
- RADIUS Policy for a WM-AD 84
- Filtering rules for a WM-AD 86
- Default Filter: Examples 93
- Multicast for a WM-AD 95
- Privacy for a WM-AD 96
- Privacy for a WM-AD for AAA 97
- A WM-AD for voice traffic 101
- Availability and Mobility 103
- Management users 111
- Network time 112
- Check Point event logging 113
- Setting up SNMP 115
- Setting SNMP Parameters 116
- Overview 123
- Summit Spy: running scans 125
- The Analysis Engine 126
- 11 Ongoing operation 131
- Altitude AP client management 133
- Client disassociate 134
- Client blacklist 135
- Health Checking 136
- Change the system log level 136
- Enable and configure Syslog 136
- Logs and alarms 141
- View the Logs 142
- View the Traces 142
- View the Audits 143
- Reports and displays 144
- View reports 146
- Glossary 147
- D (Continued) 149
- F (Continued) 151
- H (Continued) 152
- I (Continued) 153
- O (Continued) 156
- P (Continued) 157
- S (Continued) 160
- T (Continued) 162
- W (Continued) 164
- Altitude AP system states 168
- B CLI command reference 169
- CLI command reference 170
- RFC list 177
- 802.11 standards list 178
- Reference lists of standards 180
- E Support for Altitude AP 181
- F RADIUS Attributes 183
- RADIUS Accounting 184
- Account-Stop/Interim Packet 185
- Termination Codes 186
- G Logs and Events 187
- Logs and Events 188
- Critical 189
- CDR_COLLECTOR 191
- CONFIG_MANAGER 191
- EVENT_SERVER 192
- RADIUS_ACCOUNTING 194
- RADIUS_CLIENT 194
- RF_DATA_COLLECTOR 195
- RU_MANAGER 195
- SECURITY_MANAGER 196
- STARTUP_MANAGER 197
- STATS_SERVER 198
- ACCESSPOINT 200
- CPDP_AGENT_ID 203
- NSM_SERVER 205
- OSPF_SERVER 206
- PORT_INFO_J_MANAGER 206
- REDIR_ID 207
- H Regulatory Information 213
- Emissions 214
- FCC ID#: RJF-A3502 216
- Part 15 Unlicensed Antenna 217
- European Community 218
- European Spectrum Usage Rules 221
- Regulatory Information 222
- Declarations of Conformity 223
Powiązane produkty i podręczniki dla Oprogramowanie Extreme Networks Summit WM Series
(7 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.094 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji