Extreme Networks WM-4T1i Podręcznik Użytkownika Strona 34
- Strona / 46
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
3-4 WAN Module Installation and User Guide
Configuring PPP and MLPPP
config ppp authentication [off | chap | pap | chap-pap] [ports
<portlist> | multilink <groupname>]
PPP Link Username
When the local end of a link initiates a PPP connection, the local end must send the
appropriate authentication information. For PAP it sends the username and password,
for CHAP it sends the username and must respond correctly to the challenge, and for
no authentication it sends nothing. To configure the username and password used to
initiate the link, use the following command:
config ppp user <username> {encrypted} <password> [ports <portlist> |
multilink <groupname>]
The encrypted keyword is used to hide the password when the switch configuration is
displayed; it does not control whether the password is encrypted across the link during
authentication.
PPP User Accounts
When the remote end initiates the link, the local end must verify the authentication
information. The local end maintains a list of authorized user accounts and passwords.
To add a user to the list, use the following command:
create account pppuser <name> {encrypted} {<password>}
Encapsulation
The packets passed over the PPP/MLPPP link can use either bridged or routed
encapsulation. You would use bridged packets if you plan to have VLANs span the
link. You would use routed packets if the link connects two different routed networks
or separate VLANs.
Using bridged packets allows the VLAN tags to be carried across the PPP/MLPPP link.
Bridged packets are transported using the PPP Bridging Control Protocol (BCP),
described in RFC 2878. When the encapsulation is set to BCP, 802.1Q and 802.1p
information is preserved and transported across the link. On a WAN module, a VLAN
may only contain one BCP encapsulated link, but you may have multiple VLANs span
the link.
- WAN Module Installation 1
- Contents 3
- 3 Configuring PPP and MLPPP 4
- Index of Commands 4
- Introduction 5
- Conventions 6
- Convention Description 7
- Related Publications 8
- Installing the WAN Module 10
- Ports and Connectors 11
- Module LEDs 12
- Table 1-1: WAN Module LEDs 13
- Configuring the WAN Physical 17
- Red, Blue, and Yellow Alarms 18
- Cable length 19
- Facility Data Link 20
- Clock Source 20
- Inband Loopback Detection 21
- Linecoding 21
- Receiver Gain 21
- SNMP Alerts 21
- Timeslots 22
- Yellow Alarms 22
- Monitoring WAN Physical Links 24
- Remote WAN PortLocal WAN Port 25
- Enabling Loopback Mode 28
- Disabling Loopback Mode 28
- WAN Port Monitoring Commands 29
- Configuring PPP and MLPPP 31
- Configuring a PPP/MLPPP Link 33
- Encapsulation 34
- Monitoring PPP/MLPPP Links 36
- command 37
- Switch #1 38
- Safety Information 41
- FCC Certification 42
Powiązane produkty i podręczniki dla Networking Extreme Networks WM-4T1i
Networking Extreme Networks WM200 Dokumentacja
(210 strony)
(210 strony)
Networking Extreme Networks WM200 Dokumentacja
(126 strony)
(126 strony)
Networking Extreme Networks WM-4T1i Dokumentacja
(336 strony)
(336 strony)
Networking Extreme Networks WM200 Dokumentacja
(130 strony)
(130 strony)
Networking Extreme Networks 300-2 Dokumentacja
(62 strony)
(62 strony)
Networking Extreme Networks WM-4T1i Dokumentacja
(306 strony)
(306 strony)
Integra-lifesciences Sutures, Coated, Braided Polygycolic Acid, Absorba Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Gesundheit und Hygiene Integra-lifesciences Sutures, Coated, Braided Polygycolic Acid, Absorba.
Wir stellen 1 PDF-Handbücher Integra-lifesciences Sutures, Coated, Braided Polygycolic Acid, Absorba zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Komentarze do niniejszej Instrukcji